C-Frame Flywheel Press

C-Frame FLYWHEEL PRESSES: C-Frame presses without reduction gears between the drive shaft and the eccentric shaft are well suited for applications with higher production speeds for increased productivity. Suitable for blanking and stamping.

  • CE Certification
  • Steel frame (cast iron and T10 CE T15 CE)
  • Forged alloy steel shaft
  • Pneumatic clutch-brake combined units
  • Control panel with SIEMENS PLC for the adjustment of all settings and Pilz safety devices
  • Production and preset counters
  • Selector for reverse motion
  • Ram with oil collector and 6 sliding surfaces
  • Automatic and centralized lubrication system with adjustable flow
  • Automatic hydraulic overload protection (mechanical on T30CE and T40 CE)
  • Extractor unit
  • Air counterbalance cylinders

FLYWHEEL AND BACK-GEARED C-FRAME ECCENTRIC PRESSES

  • T10 – T75 / T50 – T450

C-FRAME FLYWHEEL ECCENTRIC PRESSES

Press Model Power
[KN]
Nominal speed [SPM] Variable speed* [SPM] Stroke [mm] – [in] Table-Ram distance** [mm] – [in] Working table [mm] – [in] Ram surface [mm] – [in]
T10 CE 100 190 92-230 6-40 (0,24-1,57) 210 (8,27) 240×360 (9,45×14,17) 90×150 (3,54×5,91)
T15 CE 150 165 88-220 8-60 (0,31-2,36) 260 (10,24) 300×400 (11,81×15,75) 104×230 (4,09×9,06)
T20 CE 200 155 84-210 6-60 (0,24-2,36) 300 (11,81) 300×450 (11,81×17,72) 190×278 (7,48×10,94)
T30 CE 300 145 80-200 8-76 (0,31-2,99) 350 (13,78) 360×580 (14,17×22,83) 250×350 (9,84×13,78)
T40 CE 400 145 76-190 8-78 (0,31-3,07) 375 (14,76) 380×650 (14,96×25,59) 250×350 (9,84×13,78)
T50 CE 500 140 72-180 12-110 (0,47-4,33) 400 (15,75) 440×750 (17,32×29,53) 300×450 (11,81×17,72)
T75 CE 750 120 60-130 14-140 (0,55-5,51) 450 (17,72) 500×800 (19,69×31,50) 380×560 (14,96×22,05)

C-FRAME BACK GEARED ECCENTRIC PRESSES

Press Model Power
[KN]
Nominal speed [SPM] Variable speed* [SPM] Stroke [mm] – [in] Table-Ram distance** [mm] – [in] Working table [mm] – [in] Ram surface [mm] – [in]
T50 RCE 500 80 40-100 12-110 (0,47-4,33) 400 (15,75) 440×750 (17,32×29,53) 300×450 (11,81×17,72)
T63 RCE 630 70 36-90 12-140 (0,47-5,51) 450 (17,72) 500×800 (19,96×31,50) 380×560 (14,96×22,05)
T80 RCE 800 65 34-85 14-150 (0,55-5,91) 480 (18,90) 580×900 (22,83×35,43) 380×560 (14,96×22,05)
T100 RCE 1000 60 30-75 17-180 (0,67-7,09) 520 (20,47) 650×1100 (25,60×43,31) 500×680 (19,69×26,77)
T130 RCE 1300 55 28-70 16-200 (0,63-7,78) 560 (22,05) 700×1200 (27,60×47,24) 540×740 (21,26×29,13)
T160 RCE 1600 50 24-60 15-220 (0,59-8,66) 660 (25,98) 760×1300 (29,92×51,18) 660×850 (25,98×33,46)
T200 RCE 2000 45 22-56 19-230 (0,75-9,06) 750 (29,53) 850×1450 (33,46×57,09) 680×900 (26,77×35,43)
T250 RCE 2500 42 20-50 15-220 (0,59-8,66) 780 (30,71) 900×1600 (35,43×62,99) 750×1100 (29,53×43,31)
T350 RCE 3500 34 20-50 20-250 (0,79-9,84) 800 (31,50) 1000×1800 (39,37×70,87) 880×1250 (34,65×49,21)
T450 RCE 4500 34 22-50 20-250 (0,79-9,84) 850 (33,46) 1000×1800 (39,37×70,87) 900×1400 (35,43×55,12)

[*] Distance between table and ram lower bolster plate at Upper Dead Point with maximum stroke and ram regulation screw up.

The range of mechanical eccentric presses is divided into flywheel mechanical presses from 10 to 75 Ton and back-geared presses from 50 to 450 Ton. This version allows high speed and higher productivity, having no intermediate reduction between the drive shaft and the eccentric shaft. Suitable for shearing and stamping
The version of back-geared presses allows a high-tonnage production at reduced nominal speeds, thanks to an intermediate wheel-pinion gear system between drive shaft and eccentric shaft.Suitable for shearing, stamping and small drawing

– Compliance with CE norms
– Steel frame (cast iron for  T10CE and T15CE)
– Forged alloy steel shaft
– Combined clutch-brake unit with pneumatic control
– Control Panel with SIEMENS PLC to adjust all settings, as well as Pilz security devices
– Variable stroke
– Total, partial and pre-selected  stroke counter
– Selector for reverse motion
– Oil-bath gears
– Ram with oil collector and 6 sliding surfaces
– Centralized automatic lubrication with adjustable flow
– Automatic hydraulic overload
– Extractor unit
– Ram balancing cylinders
– Motorized ram regulation system

C-Frame BACK GEARED PRESSES: C-Frame presses with an intermediate reduction gear provide higher tonnage at reduced nominal speeds. Suitable for blanking and stamping and deep drawing.

  • CE Certification
  • Steel frame
  • Forged alloy steel shaft
  • Pneumatic clutch-brake combined units
  • Control panel with SIEMENS PLC for the adjustment of all settings and Pilz safety devices
  • Production and preset counters
  • Selector for reverse motion
  • Oil bath lubrication for gears
  • Ram with oil collector and 6 sliding surfaces
  • Automatic and centralized lubrication system with adjustable flow
  • Automatic hydraulic overload protection
  • Extractor unit
  • Air counterbalance cylinders
  • Motorized ram adjustment
chrismach

About chrismach